Droop wingtips............................$295 pr + $45 crate
Efficiency of the wing is improved by reducing
vortex and smoothing airflow at the wingtip. Lift is increased and drag
reduced resulting in shorter take-off distance, higher climb rate and faster
more efficient cruise speed. Fits all team models. Made with 2 ply 7500
fiberglass cloth, epoxy resin, white epoxy primer finish, Weight 5 lbs pr
Also available in carbon fiber for $389 which saves 1.5 lb of weight and yet its stronger and more hangar rush resistant.
for mounting instructions click here
leading edge/fuselage fairing......................$125
finishes the unsightly gap between the wing and the MiniMax fuselage
Minimax foot step......................$75
This foot step is bigger and an inch deeper also has the flange all the way around not just the top part
Composite landing gear spring............$1,200 spring only
Your HiMax will ride like a Cadillac if you install
this fiberglass spring gear. This fiberglass gear flexes more then the
comparable one made out of aluminum but its much lighter. It is a little wider
for easier directional control. Cleaner installation increases cruise speed
and softer landing reduce bouncing. Total height 20 inches, the axel placement is in the range of 15.5 - 18.5 inches, total width 48
inches (unloaded), designed for up to 700 lb gross weight. Weight 11 lbs
HiMax gear intalation pix [1] [2]
[3] [4]
[5] install
intructions
I can custom make a gear spring at about 40% weight reduction over an aluminum one.
Axels for the gear.........................$80
pr
5/8 od" allows for replacing of the original
Flintstone type bushings with real wheel bearings
trike gear spring......................$1,100.
this one is for 103 trikes, powered chutes, and fighter type ultralights like Phantom Hurricane and Flightstar.
Width 47", axel height 9-13", weight only 6 Lbs.
Gear/struts fairings . . . . . . . . . . . $225 (4set)
pr
Fits to strut streamlined fairings that are 4� and 3� wide. Best to have on hand while installing the gear to assure proper fit.
Fiberglass wheel
pants.....................5 inch rims 12-13 inch wheel 6 inch wide $169
pr
Fiberglass wheel pants.....................6 inch rims 14-15 inch wheel
8 inch wide $189 pr
Strong, light weight, made from 3 ply 7500
fiberglass cloth, epoxy resin, white epoxy primer finish. The smaller one is 6
inches wide, 10 inches high, 28 inches long,, The bigger one is 8 inches wide,
11 inches high, 33 inches long.
Carbon fiber/fiberglass tail wheel spring...............$165 ea
Nice flexible, light
weight and solves the common problem of the aluminum spring getting
bent. Weight 10 oz
Molded carbon fiber tail wheel bracket with 4.75" wheel ...............$169 ea
curently not in production
Supercowl (Rotax 503 or
447)......................$265
Using free air cooling scoop frees up two more horsepower which are being robbed by the cooling fan and removes 7 lb of weight by eliminating the fan tower, fan belt and metal shrouds.
Installation application samples - [MiniMax] [Airbike][HiMax][Flighstar]
Installation pics - [1][2][3
Trike instrument pods......................$149 each
Two styles, the straight small one has room for three round gauges or two gauges and tiny tach , The bigger T-shaped one can take up to 5 gauges but is mainly intended for EIS plus whatever.
The small one is available with flat bottom or curved for a 2" tube mounting, The bigger one is curved bottom only and may need a flat piece of back up plate when mounted on a squared tube. They come in white finish.
Carbon fiber instrument panel decorative overlay.....typical single seater size $95 two seater $145
Creates the deep 3D clear carbon look. The picture doesn�t do it justice as it is impossible to capture the effect with a camera.
To order, e-mail is preferred, include full shipping address so I can get the total with shipping cost back to you
sychrovsky@mindspring.com (use for business only)
Or call 978 425 0229 , best time to call is between 2 and 5 afternoon
Mailing address
Cured Composites
1997
Shirley rd
Lancaster MA 01523
My work load is unpredictable, if you know you need a part order early.